Common Network Cable types

Cables are commonly used to carry communication signals within Local Area Networks (LAN). There are three common types of cable media that can be used to connect devices to a network and they are coaxial cable, twisted-pair cable, and fiber-optic cable.

Coaxial cable

Coaxial cable looks similar to the cable used to carry TV signal. A solid-core copper wire runs down the middle of the cable. Around that solid-core copper wire is a layer of insulation, and covering that insulation is braided wire and metal foil, which shields against electromagnetic interference. A final layer of insulation covers the braided wire.

There are two types of coaxial cabling: thinnet and thicknet. Thinnet is a flexible coaxial cable about ¼ inch thick. Thinnet is used for short-distance. Thinnet connects directly to a workstation’s network adapter card using a British Naval Connector (BNC). The maximum length of thinnet is 185 meters. Thicknet coaxial is thicker cable than thinnet. Thicknet cable is about ½ inch thick and can support data transfer over longer distances than thinnet. Thicknet has a maximum cable length of 500 meters and usually is used as a backbone to connect several smaller thinnet-based networks.

The bandwidth for coaxial cable is 10 Mbps (Mega bits per second).

Type of Cable used to wire Local Area Networks (LAN) these days is Twisted Pair cable. It is extremely difficult to find a live business network using coaxial cable.

Twisted Pair Cable

Twisted-pair cable is the most common type of cabling you can see in today's Local Area Networks (LAN) networks. A pair of wires forms a circuit that can transmit data. The pairs are twisted to provide protection against crosstalk. Crosstalk is the undesired signal noise generated by the Electro-Magnetic fields of the adjacent wires.

When a wire is carrying a current, the current creates a magnetic field around the wire. This field can interfere with signals on nearby wires. To eliminate this, pairs of wires carry signals in opposite directions, so that the two magnetic fields also occur in opposite directions and cancel each other out. This process is known as cancellation.

Two Types of Twisted Pairs are Shielded Twisted Pair (STP) and Unshielded Twisted Pair (UTP). Unshielded twisted-pair (UTP) cable is the most common networking media. Unshielded twisted-pair (UTP) consists of four pairs of thin, copper wires covered in color-coded plastic insulation that are twisted together. The wire pairs are then covered with a plastic outer jacket. UTP cables are of small diameter and it doesn’t need grounding. Since there is no shielding for UTP cabling, it relies only on the cancellation to avoid noise.

Colors used for Twisted Pair wires are Orange, Orange-White, Blue, Blue-White, Green, Green-White, Brown and Brown-White. Following image shows a dissected Unshielded Twisted Pair cable.

The connector used on a UTP cable is called as RJ-45 (Registered Jack 45) connector. Below picture shows an RJ45 jack, attached to UTP cable. Eight color-coded wires inside Twisted-Pair cable is attached to eight pins in a RJ45 jack as shown below. Each wire in the Twisted Pair cable is crimped into 8 pins in the RJ45 jack.

One end of the Unshielded Twisted Pair cable with RJ45 jacks attached is plugged in to computer's Ethernet NIC card port and other end end is plugged to the wall mount plate with female RJ45 port (receptacle), as shown below.

From the wall mount RJ45 female receptacle, Unshielded Twisted Pair cable is wired to the Local Area Network (LAN) switches.

UTP cabling has different categories. Each category of UTP cabling was designed for

a specific type of communication or transfer rate. The most popular categories in use today is 5e and 6, which can reach transfer rates of over 1000 Mbps (1 Gbps).

Unshielded Twisted Pair cables support a maximum distance of 100 Meters (from NIC Card to Switch Port), without signal distortion.

The following table shows different UTP categories and corresponding transfer rate.

Optical Fiber Cabling

Optical Fiber cables use optical fibers that carry digital data signals in the form of modulated pulses of light. An optical fiber consists of an extremely thin cylinder of glass, called the core, surrounded by a concentric layer of glass, known as the cladding. There are two fibers per cable—one to transmit and one to receive. The core also can be an optical-quality clear plastic, and the cladding can be made up of gel that reflects signals back into the fiber to reduce signal loss.

There are two types of fiber optic cable: Single Mode Fibre (SMF) and Multi Mode Fibre (MMF).

1. Single Mode Fibre (SMF) uses a single ray of light to carry transmission over long distances.

2. Multi Mode Fibre (MMF) uses multiple rays of light simultaneously with each ray of light running at a different reflection angle to carry the transmission over short distances

Chapter 1 :- Introduction to Computer Networking

Chapter 2 :- What is a Computer Network

Chapter 3 :- Why we need computer networks

Chapter 4 :- Client Operating Systems

Chapter 5 :- Common Network Application Software

Chapter 6 :- LAN and WAN

Chapter 7 :- CAN and MAN

Chapter 8 :- Peer-to-Peer networks and Client-Server networks

Chapter 9 :- Centralized and Distributed Computer Networks

Chapter 10 :- Internetworks, Internet, Intranet and Extranet

Chapter 11 :- What is a Network Protocol

Chapter 12 :- Difference between Proprietary and Standard Protocols